Brass Nozzle Kit MK8 24-Pack compatible with Creality CR-10 Series, CR10S, Ender 3, Ender 5
24-piece MK8 brass extruder nozzle kit with multiple sizes from 0.2mm to 1.0mm. Includes cleaning needles and a wrench.
Key facts
- Part type
- MK8 Nozzle Kit
- Included
- 24-pack
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Creality | Creality CR10S | Fits |
| Creality Ender 5 | Fits | |
| Creality CR-10 Series | Fits | |
| Creality Ender 3 | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Creality: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
General manufacturer guidance: exact label position can vary by model.
MK8 Nozzle Kit specifications
- Material
- Premium Brass
- Input Diameter
- 2.00mm
- Output Diameters
- 0.2mm, 0.4mm, 0.6mm, 0.8mm, 1.0mm
- Thread
- M6
- Thread Length
- 5mm
- Filament Compatibility
- 1.75mm PLA ABS
Installation guide - Installing a parts kit
General guidance for this part type - always follow your device manual- As needed for the individual parts
- Photograph each step as you take things apart; it makes reassembly much easier.
- 1Switch off and unplug. Power the device down and disconnect it.
- 2Check the contents. Lay out the kit and compare it with the pack list on this page.
- 3Replace one part at a time. Swap each part completely before starting the next, so nothing gets mixed up.
- 4Keep the old parts. Hold on to them until the device runs normally with the new ones.
- 5Test. Run a short cycle and listen for unusual noise before regular use.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Under-extrusion or inconsistent lines
- 02Clogging that cleaning does not fix
- 03Worn or enlarged nozzle opening
More parts for Creality CR10S
See all Creality CR10S parts
More parts for Creality Ender 3
See all Creality Ender 3 parts
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this mk8 nozzle kit fit?
Our team verified it for Creality CR10S, Creality Ender 5, Creality CR-10 Series, Creality Ender 3. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your device label and compare it with the table above. Our fit guarantee covers verified models.
+What's in the box?
Pack size: 24-pack, as listed for this part. Check the photos and specifications for the exact contents.
+What is the mk8 nozzle kit made of?
Listed material: Premium Brass.
+Is it hard to install?
Install difficulty: Easy · no tools, a few minutes. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.