HEPA Filter 2-Pack compatible with Roborock G10, S7, S7 MaxV Plus, S7 MaxV Ultra, S70, S75, T7S, T7S Plus
A pack of two HEPA filters designed to capture 99.97% of particles as small as 0.3 microns. These washable and reusable filters help maintain your robot vacuum's peak suction performance.
Key facts
- Part type
- HEPA Filter
- Included
- 2-pack
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Roborock | Roborock T7S Plus | Fits |
| Roborock S7 MaxV Ultra | Fits | |
| Roborock T7S | Fits | |
| Roborock S7 | Fits | |
| Roborock S75 | Fits | |
| Roborock G10 | Fits | |
| Roborock S70 | Fits | |
| Roborock S7 MaxV Plus | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Roborock: Lift the top cover. The model label is beside the dustbin; also on the bottom of the robot.
General manufacturer guidance: exact label position can vary by model.
HEPA Filter specifications
- Material
- Plastic
- Compatibility
- Roborock S7 Series
Installation guide - Replacing a filter
General guidance for this part type - always follow your device manual- No tools required in most cases
- Do not wash a filter unless it is marked washable; wet HEPA media stops filtering.
- If the filter does not sit flush, stop and recheck the model on this page.
- 1Switch off and unplug. Power the device down and unplug it.
- 2Open the filter compartment. It is usually behind a front or back cover, or inside the dustbin on vacuums. Your manual shows the exact spot.
- 3Remove the old filter. Note how it sat, especially any airflow arrow or rubber seal facing the motor. Tap dust off into a bag outdoors.
- 4Fit the new filter. Take off all plastic wrap, seat it the same way round until it sits flush with its seal fully in contact, and never force it.
- 5Close and test. Close the cover, run the device and check for normal sound and airflow. Reset the filter reminder if your device has one.
Read the full guide: How to Replace an Air Purifier HEPA Filter →
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Suction is weaker than usual
- 02Dust or odors escape from the exhaust
- 03Filter is grey, clogged or torn
More parts for Roborock S7
See all Roborock S7 parts
FP-9A8250
FP-A3956C×1
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this hepa filter fit?
Our team verified it for Roborock T7S Plus, Roborock S7 MaxV Ultra, Roborock T7S, Roborock S7, Roborock S75, Roborock G10 and 2 more. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your device label and compare it with the table above. Our fit guarantee covers verified models.
+What's in the box?
Pack size: 2-pack, as listed for this part. Check the photos and specifications for the exact contents.
+What is the hepa filter made of?
Listed material: Plastic.
+Is it hard to install?
Install difficulty: Easy · no tools, a few minutes. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.