Hall Effect Joystick Sensor 4-Pack compatible with Microsoft Xbox One; Sony PlayStation 4 Pro, PS4, PS4 Controller, PS5 (Grey)
High-quality 3D Hall Effect analog joystick sensors designed to fix stick drift and dead zones. These wear-resistant sensors provide a long service life and reliable centering for intense gaming.
Key facts
- Part type
- Hall Effect Joystick Sensor
- Included
- 4-pack
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Microsoft | Microsoft Xbox One | Fits |
| Sony | Sony PS5 | Fits |
| Sony PlayStation 4 Pro | Fits | |
| Sony PS4 | Fits | |
| Sony PS4 Controller | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Microsoft, Sony: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
General manufacturer guidance: exact label position can vary by model.
Hall Effect Joystick Sensor specifications
- Technology
- Hall Effect (Magnetic)
- Quantity
- 4 Pieces
Installation guide - Replacing a thumbstick or joystick
General guidance for this part type - always follow your device manual- Tri-wing or Phillips screwdriver
- Plastic spudger
- Soldering iron and desoldering wick, for soldered joysticks only
- Hall effect joysticks can need calibration on first use; do this before closing if the controller allows it.
- 1Thumbstick caps only. Pull the old cap straight up firmly, line up the new cap with the stick's shaft and press it straight down until it is fully seated. You can stop here.
- 2Open the controller. For a full joystick, switch the controller off, remove its screws and release the clips along the grips. Disconnect the battery if it has a plug.
- 3Check how the joystick connects. Joy-Con style joysticks plug in with a ribbon and a small lock. PlayStation and Xbox joysticks are soldered to the board and need desoldering.
- 4Fit the new joystick. Seat the ribbon fully and close its lock, or solder each pin cleanly with no bridges between pins.
- 5Test and calibrate. Reassemble, then run the stick calibration in your console's settings and check for drift before regular play.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Controller drifts without touching the stick
- 02Cap is worn, slippery or torn
- 03Stick feels loose or unresponsive
More parts for Microsoft Xbox One
See all Microsoft Xbox One parts
FP-69C4F2×4
FP-8E4291×4
More parts for Sony PS4
See all Sony PS4 parts
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this hall effect joystick sensor fit?
Our team verified it for Microsoft Xbox One, Sony PS5, Sony PlayStation 4 Pro, Sony PS4, Sony PS4 Controller. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your device label and compare it with the table above. Our fit guarantee covers verified models.
+What's in the box?
Pack size: 4-pack, as listed for this part. Check the photos and specifications for the exact contents.
+Is it hard to install?
Install difficulty: Advanced · mechanical experience needed. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.