Dummy Battery LP-E6 compatible with Canon 60DA, EOS 6D, EOS 60D, EOS R5
High-efficiency LP-E6 dummy battery with a Type-C input supporting PD and QC fast charging protocols. The integrated power indicator light provides clear status updates during continuous shooting sessions.
Key facts
- Part type
- Dummy Battery Coupler
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Canon | Canon EOS 60D | Fits |
| Canon EOS 6D | Fits | |
| Canon 60DA | Fits | |
| Canon EOS R5 | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Canon: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
General manufacturer guidance: exact label position can vary by model.
Dummy Battery Coupler specifications
- Input Voltage
- 9-20V (Type-C)
- Conversion Efficiency
- Up to 98%
- Fast Charging Protocols
- PD 2.0/3.0, QC 2.0/3.0, Samsung AFC, Huawei FCP
- Material
- Plastic
Installation guide - Replacing a battery
General guidance for this part type - always follow your device manual- Small screwdriver, only if the battery cover is screwed shut
- Match the voltage and battery code printed on the old battery.
- If the device does not power on, reseat the plug before assuming a fault.
- If the old battery is swollen, do not press, bend or puncture it. Tape over its contacts and take it to a battery recycling point; never put it in household trash.
- 1Switch off and unplug. Turn the device off (robot vacuums: switch off the main power switch) and disconnect the charger.
- 2Open the battery compartment. Most use a sliding door, a latch, or a cover with two small screws on the underside. Battery packs on tools and vacuums slide out after pressing the release button.
- 3Remove the old battery. Lift it out by its tab. If it has a plug, squeeze the plug's latch and pull the plug body, never the wires.
- 4Fit the new battery. Place it the same way round, push the plug in until it clicks and make sure the battery sits flat without pinching wires.
- 5Close and charge. Refit the cover and charge to full before first use.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Much shorter run time per charge
- 02Device will not hold a charge or shuts off early
- 03Battery gets unusually hot
- 04Swelling or leaking (stop using it)
More parts for Canon 60DA
See all Canon 60DA parts
FP-4699E6
FP-A110B0
More parts for Canon EOS 6D
See all Canon EOS 6D parts
FP-AB498612 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this dummy battery coupler fit?
Our team verified it for Canon EOS 60D, Canon EOS 6D, Canon 60DA, Canon EOS R5. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your device label and compare it with the table above. Our fit guarantee covers verified models.
+What voltage does it use?
Listed voltage: 9-20V (Type-C). It must match the voltage of your original part.
+What is the dummy battery coupler made of?
Listed material: Plastic.
+Is it hard to install?
Install difficulty: Moderate · basic hand tools. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.