Integrated LED Tail Light compatible with Yamaha Tenere 700, Tenere 700 Rally, Tenere 700 World Raid, XTZ700
An integrated LED tail light featuring running, brake, and turn signal functions. Constructed from PMMA, PC, and PP with a smoke lens and E32 certification for traffic safety.
Key facts
- Part type
- LED Tail Light
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Yamaha | Yamaha Tenere 700 | Fits |
| Yamaha XTZ700 | Fits | |
| Yamaha Tenere 700 Rally | Fits | |
| Yamaha Tenere 700 World Raid | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Yamaha: Use your 17-character VIN. It's on the driver-side dashboard at the base of the windshield and on the driver's door jamb sticker. The year is in the 10th character. Also check your registration or the owner's manual.
General manufacturer guidance: exact label position can vary by model.
LED Tail Light specifications
- Material
- PMMA+PC+PP
- Running Light Power
- 12V/0.3W
- Brake Lamp Power
- 12V/4W
- Turn Signal Power
- 12V/2W
- Cable Length
- 400mm
- Certification
- E32
Installation guide - Replacing a tail light assembly
General guidance for this part type - always follow your device manual- Socket set or nut driver
- Plastic trim tool
- Masking tape
- Check for water marks in the trunk later; a gap in the gasket lets water in.
- 1Make it safe. Engine off, lights off. Open the trunk or tailgate.
- 2Reach the fixings. Remove the access cover or trim panel inside the trunk behind the lamp; the nuts are on the back of the lamp. Some lamps also have screws on the edge facing the open tailgate.
- 3Remove the old lamp. Unplug the connector by pressing its tab, undo the nuts and pull the lamp straight back. Put tape on the paint around the lamp first; ball clips need a firm, wiggling pull.
- 4Fit the new lamp. Move the bulbs across if the new lamp has none, check its gasket is seated, push it onto the studs and tighten the nuts snug, not hard, since the housing is plastic.
- 5Test every function. With a helper, check tail, brake, turn, reverse and hazard lights before refitting the trim.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Light is out, dim or flickering
- 02Cracked, foggy or yellowed lens
- 03Moisture or water inside the housing
- 04Dashboard bulb-out warning
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this led tail light fit?
Our team verified it for Yamaha Tenere 700, Yamaha XTZ700, Yamaha Tenere 700 Rally, Yamaha Tenere 700 World Raid. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your vehicle registration or VIN and compare it with the table above. Our fit guarantee covers verified models.
+What is the led tail light made of?
Listed material: PMMA+PC+PP.
+Does it have any certifications?
Listed certification: E32, as stated by the manufacturer.
+Is it hard to install?
Install difficulty: Moderate · basic hand tools. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.