Filter Media Pads and Impeller
Six-pack of dual-layer aquarium filter media pads featuring 30 PPI foam and 2000D fiber to trap debris and fish waste. Includes a replacement impeller with a durable zirconia shaft for consistent filtration performance. Designed to maintain clear water and reduce odors in freshwater tanks with a recommended 3-week replacement cycle.
Key facts
- Part type
- Filter Media And Impeller Kit
- Included
- 6 Filter Pads + 1 Impeller
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listedTo see if it fits your vehicle, compare these published specifications with your original part:
- Impeller Shaft Material
- Zirconia
- Filter Pad Material
- Polyurethane Foam, Polyester Fiber
- Filter Pad Color
- White & Black
- Dimensions
- 8.4 x 6.2 x 1.3 in / 214.5 x 158.3 x 32 mm
Not sure? Send us your exact model number and we will confirm the fit before you order.
We have not confirmed a model list for this part yet. Match it with the published specifications above, or send us your exact model number and we will confirm before you order.
Filter Media And Impeller Kit specifications
- Impeller Shaft Material
- Zirconia
- Filter Pad Material
- Polyurethane Foam, Polyester Fiber
- Filter Pad Color
- White & Black
- Dimensions
- 8.4 x 6.2 x 1.3 in / 214.5 x 158.3 x 32 mm
Installation guide - Replacing a filter
General guidance for this part type - always follow your device manual- No tools required in most cases
- Do not wash a filter unless it is marked washable; wet HEPA media stops filtering.
- If the filter does not sit flush, stop and recheck the model on this page.
- 1Switch off and unplug. Power the device down and unplug it.
- 2Open the filter compartment. It is usually behind a front or back cover, or inside the dustbin on vacuums. Your manual shows the exact spot.
- 3Remove the old filter. Note how it sat, especially any airflow arrow or rubber seal facing the motor. Tap dust off into a bag outdoors.
- 4Fit the new filter. Take off all plastic wrap, seat it the same way round until it sits flush with its seal fully in contact, and never force it.
- 5Close and test. Close the cover, run the device and check for normal sound and airflow. Reset the filter reminder if your device has one.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Reduced water flow or pressure
- 02Engine or outboard overheating (marine)
- 03Cracked or worn impeller vanes
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models has your team verified?
None yet. The title shows the models this part is designed for, but our team hasn't confirmed the fit. Compare the part with your old one before ordering.
+What's in the box?
Pack size: 6 Filter Pads + 1 Impeller, as listed for this part. Check the photos and specifications for the exact contents.
+What are the dimensions?
Listed size: 8.4 x 6.2 x 1.3 in / 214.5 x 158.3 x 32 mm. Measure your old filter media and impeller kit to compare.
+Is it hard to install?
Install difficulty: Advanced · mechanical experience needed. Step by step instructions are on this page.
+How fast will it arrive?
This part is in stock in the USA: delivery within 3 to 8 business days, free shipping in the US.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.