Crankshaft Position Sensor Plug compatible with Ford Contour, Ikon, Ka; Mercury Contour
Small size with magnetic induction type technology.
Key facts
- Part type
- Crankshaft Position Sensor Plug
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| Mercury | Mercury Contour | Fits |
| Ford | Ford Contour | Fits |
| Ford Ka | Fits | |
| Ford Ikon | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Mercury, Ford: Use your 17-character VIN. It's on the driver-side dashboard at the base of the windshield and on the driver's door jamb sticker. The year is in the 10th character. Also check your registration or the owner's manual.
General manufacturer guidance: exact label position can vary by model.
Crankshaft Position Sensor Plug specifications
- Placement
- Crankshaft
- Engine Compatibility
- 1.6L, 2.0L
Installation guide - Replacing an engine or wheel sensor
General guidance for this part type - always follow your device manual- Socket set (oxygen sensors need an O2 sensor socket)
- Penetrating oil
- OBD2 scanner
- If the same code returns, check the connector and wiring before suspecting the new sensor.
- 1Make it safe. Engine off and cool (exhaust parts stay hot for a long time). Raise the car on axle stands if the sensor is underneath.
- 2Follow the wire. Trace the sensor's wire to its connector, unplug it and unclip the wire from its holders, noting the route.
- 3Remove the old sensor. Soak rusty threads with penetrating oil first. Oxygen sensors unscrew with the O2 socket; wheel speed and crank sensors usually have one bolt and twist out. Clean rust from the mounting hole.
- 4Fit the new sensor. Keep anti-seize off an oxygen sensor's tip (new ones often come pre-coated on the threads). Lightly oil an O-ring, seat the sensor fully and route the wire through the original clips, away from hot or moving parts.
- 5Clear codes and test. Reconnect, clear the fault codes with an OBD2 scanner and drive to check the warning light stays off.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
Maintenance check
Signs it's time to replace
- 01Engine cranks but will not start, or stalls while driving
- 02Intermittent misfires or rough running
- 03Check engine light is on
- 04Tachometer behaves erratically
More parts for Mercury Contour
See all Mercury Contour parts
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this crankshaft position sensor plug fit?
Our team verified it for Mercury Contour, Ford Contour, Ford Ka, Ford Ikon. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your vehicle registration or VIN and compare it with the table above. Our fit guarantee covers verified models.
+Which side or position is it for?
Listed position: Crankshaft. Check the side before ordering; left and right parts differ.
+Is it hard to install?
Install difficulty: Moderate · basic hand tools. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.