Skip to content
Fitly Parts
FP-4462CC8E

Crankshaft & Camshaft Sensor Set 2-Pack compatible with Ford Mondeo MK3, Ranger

Crankshaft & Camshaft Sensor Set for Ford Ranger
No reviews yet
2-packCrankshaft & Camshaft Sensors
For Ford Mondeo MK3 +1 more
Skill levelAdvanced · mechanical experience needed

A replacement set including both crankshaft and camshaft position sensors.

Key facts

Part type
Crankshaft And Camshaft Position Sensor Set
Included
2-pack
Type
Aftermarket replacement

Compatibility matrix

Only models verified by our team are listed
This one part fits every model listed below. No need to open each model, just add this item to your cart.
Parts forModelThis part
FordFord Ranger Fits
Ford Mondeo MK3 Fits

Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.

Where to find your model number

  • Ford: Use your 17-character VIN. It's on the driver-side dashboard at the base of the windshield and on the driver's door jamb sticker. The year is in the 10th character. Also check your registration or the owner's manual.

General manufacturer guidance: exact label position can vary by model.

Crankshaft And Camshaft Position Sensor Set specifications

Interchange Part Number
BK21-6C315-AC, 6C1112K073AC, BK216C315AA

Installation guide - Replacing an engine or wheel sensor

General guidance for this part type - always follow your device manual
Tools
  • Socket set (oxygen sensors need an O2 sensor socket)
  • Penetrating oil
  • OBD2 scanner
Tips
  • If the same code returns, check the connector and wiring before suspecting the new sensor.
  1. 1Make it safe. Engine off and cool (exhaust parts stay hot for a long time). Raise the car on axle stands if the sensor is underneath.
  2. 2Follow the wire. Trace the sensor's wire to its connector, unplug it and unclip the wire from its holders, noting the route.
  3. 3Remove the old sensor. Soak rusty threads with penetrating oil first. Oxygen sensors unscrew with the O2 socket; wheel speed and crank sensors usually have one bolt and twist out. Clean rust from the mounting hole.
  4. 4Fit the new sensor. Keep anti-seize off an oxygen sensor's tip (new ones often come pre-coated on the threads). Lightly oil an O-ring, seat the sensor fully and route the wire through the original clips, away from hot or moving parts.
  5. 5Clear codes and test. Reconnect, clear the fault codes with an OBD2 scanner and drive to check the warning light stays off.

This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.

Maintenance check

Signs it's time to replace

  1. 01Engine cranks but will not start, or stalls while driving
  2. 02Intermittent misfires or rough running
  3. 03Check engine light is on
  4. 04Tachometer behaves erratically

More parts for Ford Mondeo MK3

See all Ford Mondeo MK3 parts

More parts for Ford Ranger

See all Ford Ranger parts
Oxygen Sensors compatible with Ford Explorer, F-150, RangerFP-6A59AF×2
Fits 3 models
For Ford Explorer, F-150
Oxygen Sensors F-150
$52.99
Axle Shaft Oil Seal compatible with Ford Edge, Escape, Explorer, Explorer Sport, Flex, Fusion, Ranger, Taurus, Taurus XFP-9EAF62
Fits 9 models
For Ford Edge, Escape
Axle Shaft Oil Seal
$27.99
Crankshaft Position Sensor compatible with Ford Escape, Fusion, Ranger; Mazda 6, CX-9, MPV; Mercury Mariner, MilanFP-EFEBCA
Fits 8 models
For Ford Escape, Fusion
Crankshaft Position Sensor 6, CX-9
$34.99

12 month warranty on every part

Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.

Warranty & returns policy

Customer reviews

No reviews yet

Bought this part? Be the first to share how it fit and how it held up.

Questions & answers

+Which models does this crankshaft and camshaft position sensor set fit?

Our team verified it for Ford Ranger, Ford Mondeo MK3. The full list is in the compatibility table above.

+How do I make sure it fits my exact model?

Find the model number on your vehicle registration or VIN and compare it with the table above. Our fit guarantee covers verified models.

+What's in the box?

Pack size: 2-pack, as listed for this part. Check the photos and specifications for the exact contents.

+What part numbers does it replace?

Listed reference numbers: BK21-6C315-AC, 6C1112K073AC, BK216C315AA. Compare them with the number on your old crankshaft and camshaft position sensor set.

+Is it hard to install?

Install difficulty: Advanced · mechanical experience needed. Step by step instructions are on this page.

+How fast will it arrive?

US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.

+Is there a warranty?

Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.

$54.99
1