75mm Heater Ducting Y Piece and Vent Outlet Kit for Webasto and Eberspacher
A comprehensive 75mm warm air outlet kit featuring a 360-degree rotating vent and a Y-branch splitter for diesel heater systems. Ideal for dividing airflow or adding outlets to existing Eberspacher, Webasto, or Propex setups. Includes two heater ducts, two vent outlets, a Y-branch, and four hose clips.
01Key facts
- Part type
- Heater Ducting Kit
- Category
- Cars & auto
- Part no. (MPN)
- Not published
- Pack
- 9 piece kit (2 ducts, 2 vents, 1 Y branch, 4 clips)
- Verified models
- 3
- Brands covered
- 3
- Customer rating
- No reviews yet
- Type
- Aftermarket replacement
02Compatibility matrix
Only models verified by our team are listed| Brand | Model | Status | Parts for model |
|---|---|---|---|
| Webasto | Webasto Heater Systems | Verified | View → |
| Eberspacher | Eberspacher Heater Systems | Verified | View → |
| Propex | Propex Heater Systems | Verified | View → |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- Webasto: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
- Webasto Heater Systems — model-specific location not yet confirmed; use the brand guidance above.
- Eberspacher: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
- Eberspacher Heater Systems — model-specific location not yet confirmed; use the brand guidance above.
- Propex: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
- Propex Heater Systems — model-specific location not yet confirmed; use the brand guidance above.
General manufacturer guidance — exact label position can vary by model.
03Specifications
Catalog-normalized- Material
- Plastic, Metal
- Diameter
- 75mm / 2.95in
- Vent Height
- 60mm / 2.36in
- Rotation
- 360 Degrees
04Additional attributes
Reference data - not independently verified| Variant | A |
Attributes above are reference values from the supply chain. They are shown for comparison only and are not a verified measurement of this part.
05How to check this part
- Match the complete model name or number against the verified models above.
- Compare the part type, pack contents and any published specifications to the part you are replacing.
- Where a required dimension or connector is not published, contact us rather than treating missing information as a match.
06Supplier vs manufacturer cross-check
What the listing claims, compared with official manufacturer guidance| Topic | Supplier listing | Manufacturer guidance | Our check |
|---|---|---|---|
| Compatibility | Model list claimed in the listing | Match the model number on your device label | 3 models verified |
| Specifications | 4 attributes published | Compare with the original part listed in your device manual | Reference only, not measured by us |
| Installation | No official instructions supplied | Follow your device manufacturer's manual | Our guide below follows manufacturer guidance |
Where the supplier and the manufacturer differ, follow the manufacturer.
07Installation guide - Installing a maintenance kit
General guidance for this part type - always follow your device manual- As required by the individual parts
- Photograph each step as you disassemble - it makes reassembly much easier.
- 1Switch the device off and unplug it (or remove the battery) before starting.
- 2Lay out all kit contents and compare them against the pack list on this page.
- 3Replace one component at a time, following the general guidance for each part type (filter, brush, roller, etc.).
- 4Keep old parts until you have confirmed the device runs normally with the new ones.
- 5Run a short test cycle and listen for unusual noise before regular use.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
12-month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you — claim it straight from your order page.
07Customer reviews
No reviews yet. Bought this part? Be the first to review it.
Questions & answers
Questions & answers
+What's in the box?
Pack size: 9 piece kit (2 ducts, 2 vents, 1 Y branch, 4 clips), as listed for this part. Check the photos and specifications for the exact contents.
+What is it made of?
Listed material: Plastic, Metal.
+Which models has your team verified?
3 models are verified, see the compatibility table above.
+How do I install the heater ducting kit?
Follow the installation guide on this page together with your device's user manual. Always switch off and unplug the device first.
+How long does shipping take?
Free to the US, $4.99 to the other 15 countries we ship to. See Shipping & returns for the estimated window to your country.
+Is there a warranty?
Yes, every part comes with a 12-month warranty. You can file a claim from the order page in your account.
+How do I know the heater ducting kit fits my model?
Check the "Verified compatible with" list. Only models our team has confirmed appear there. If your model isn't listed, the fit hasn't been confirmed yet.
+Is this an original manufacturer (OEM) part?
No. Fitly Parts sells compatible aftermarket parts. Brand and model names are used only to describe compatibility.
+What if it doesn't fit?
Parts marked as compatible are covered by our fit guarantee - we'll replace it or refund you.
+Can I save my devices?
Yes. Add your models under My devices and every part that fits them gets a "Fits your…" badge across the store.
More in our fit guarantee, returns policy and shipping.
