Inch Chainsaw Chain 72DL 18 compatible with John Deere 72DL; Lectric 72DL; Makita 72DL; mcculloch 72DL; Poulan 72DL (18 inch 72DL)
This 18-inch replacement chainsaw chain is crafted from high-toughness #65 manganese steel with a full chisel design for smooth, efficient cuts. It features heat-treated rivets and a hard chrome outer layer to provide enhanced wear resistance and reduced vibration during operation.
Key facts
- Part type
- Chainsaw Chain
- Included
- 1-pack
- Type
- Aftermarket replacement
Compatibility matrix
Only models verified by our team are listed| Parts for | Model | This part |
|---|---|---|
| John Deere | john deere 72DL | Fits |
| Makita | makita 72DL | Fits |
| Mcculloch | mcculloch 72DL | Fits |
| Lectric | lectric 72DL | Fits |
| Poulan | poulan 72DL | Fits |
Only the models listed above have a confirmed catalog fit. If yours is absent, compatibility is unknown, not ruled out. Compare the exact model identifier and any published dimensions or connectors before ordering.
Where to find your model number
- John Deere, Makita, Mcculloch, Lectric, Poulan: Usually on the rating label under or on the back of the device. Your owner's manual also lists the model number.
General manufacturer guidance: exact label position can vary by model.
Chainsaw Chain specifications
- Bar Length
- 18 inch
- Drive Links
- 72 DL
- Pitch
- 3/8 inch LP
- Gauge
- 0.050 inch / 0.058 inch
- Material
- #65 Manganese Steel
Installation guide - Replacing a saw chain
General guidance for this part type - always follow your device manual- Combination wrench (scrench)
- Cut resistant gloves
- Match pitch, gauge and drive link count printed on the bar to the chain on this page.
- 1Make the saw safe. Switch it off, remove the battery or disconnect the spark plug lead, and wear gloves.
- 2Remove the old chain. Loosen the bar nuts, take off the side cover and lift the chain off the bar and sprocket.
- 3Fit the new chain. Lay it in the bar groove with the cutting edges on top pointing away from the engine, and around the sprocket.
- 4Tension and tighten. Refit the cover, adjust the tensioner until the chain sits snug on the bar yet pulls round freely by hand, then tighten the bar nuts.
- 5Oil and recheck. Fill the chain oil and recheck tension after the first few minutes of cutting, as new chains stretch.
This is general guidance for the part type, not a model-specific procedure. If the part does not fit without force, stop and recheck compatibility.
12 month warranty on every part
Every part we sell is covered for 12 months from delivery. If it fails in normal use, we replace it or refund you , claim it straight from your order page.
Customer reviews
No reviews yet
Bought this part? Be the first to share how it fit and how it held up.
Questions & answers
+Which models does this chainsaw chain fit?
Our team verified it for john deere 72DL, makita 72DL, mcculloch 72DL, lectric 72DL, poulan 72DL. The full list is in the compatibility table above.
+How do I make sure it fits my exact model?
Find the model number on your device label and compare it with the table above. Our fit guarantee covers verified models.
+What's in the box?
Pack size: 1-pack, as listed for this part. Check the photos and specifications for the exact contents.
+What pitch, gauge and drive link count is the chain?
Pitch: 3/8 inch LP. Gauge: 0.050 inch / 0.058 inch. Drive links: 72 DL. All three must match your bar.
+What is the chainsaw chain made of?
Listed material: #65 Manganese Steel.
+Is it hard to install?
Install difficulty: Moderate · basic hand tools. Step by step instructions are on this page.
+How fast will it arrive?
US orders arrive in 7 to 15 business days with free shipping. Other countries are shown at checkout.
+Is there a warranty?
Yes, a 12-month warranty is included, and you can extend it at checkout. Returns are accepted within 30 days.