Skip to content
Fitly Parts

How to Replace the Inner Tube on a Xiaomi 1S

Quick answer

To replace a Xiaomi 1S electric scooter inner tube, remove the affected wheel following the owner's manual, release the remaining air, open the tire, and fit a compatible tube without pinching it. Confirm your scooter model, tire size markings, and valve configuration before ordering; this is a hands-on tire repair that may be better handled by a scooter repair shop.

The inner tube holds air inside the Xiaomi 1S scooter's pneumatic tire, helping the wheel support the rider and cushion bumps. A leaking tube can leave the tire soft or flat, so stop riding until the problem is repaired. The listings supplied here are for electric scooter inner tubes, not robot vacuum parts, despite the supplied device category. Replacing the tube also gives you a chance to inspect the tire and rim for anything that could puncture the new one.

Compatible parts in stock

Signs it needs replacing

  • The tire becomes soft again after inflation: air may be escaping through a puncture, damaged tube, or leaking valve.
  • You hear hissing near the tire or valve: an audible air leak needs to be located before deciding whether the tube must be replaced.
  • Soapy water forms growing bubbles at the valve or on an inflated tube removed from the tire: bubbles reveal an air leak.
  • The removed tube has a split, puncture, or tear around the valve base: visible tube damage is a reason to replace it and check for the cause.

Confirm your exact model

Find the exact scooter model on its identification label or in the owner's manual and confirm that it is a Xiaomi 1S or Mi 1S named in the listing. Then compare the tire sidewall and old tube markings with the replacement specifications, including size and valve configuration. The supplied listings use 50/75-6.1 and 8 1/2x2-156 as tube specification identifiers, not as Xiaomi scooter model numbers.

General replacement steps

These are general instructions. Exact access panels, latches and part orientation vary by model, always follow your device manufacturer's manual first.

  1. 1

    Switch off and unplug. Disconnect the device from power and let hot parts cool.

  2. 2

    Find the part. Check your device manual for the access panel, latches or screws; photograph each step as you go.

  3. 3

    Remove the old part. Note its orientation and any connectors, and release connectors by their plug body, never the wires.

  4. 4

    Compare and fit. Hold the old and new parts side by side, then fit the new one the same way round without forcing it.

  5. 5

    Reassemble and test. Refit covers, reconnect power and run a short test before regular use.

Choosing the right replacement

  • Choose a listing that explicitly names Xiaomi 1S or Mi 1S compatibility; shared compatibility with M365 or Pro2 alone is not a substitute for checking your scooter.
  • Compare the complete size markings, not just the 8.5-inch description. One listing specifies 8 1/2x2 (50/75-6.1), while another specifies 8 1/2x2-156 and a 156 mm inner diameter; verify the match against your existing setup.
  • Compare the valve shape, angle, and access with your old tube and the listing photos. The supplied specifications do not establish valve compatibility.
  • The explicitly labeled 2-pack provides two tubes. The other listings do not state a pack quantity, so confirm the quantity before ordering.
  • The 2-pack and thickened butyl rubber listings describe front and rear wheel use. Still check the affected wheel's tire markings, especially if its tire or wheel has been changed.

Frequently asked questions

Which inner tube fits a Xiaomi 1S electric scooter?

All three supplied listings name Xiaomi 1S or Mi 1S compatibility and describe 8.5-inch tubes. Confirm the full tire size markings and valve configuration against your existing tube before choosing one; these are aftermarket replacements, not identified as genuine Xiaomi parts.

Can I use any universal 8.5-inch inner tube on a Xiaomi 1S?

Do not choose by diameter alone: the tube must match the tire's size requirements and have a valve that fits and remains accessible through the rim. Check the full listing specifications and your owner's manual rather than assuming every 8.5-inch tube is interchangeable.

How do I replace the inner tube on a Xiaomi 1S myself?

Turn the scooter off, disconnect the charger, support it securely, and follow the owner's manual for wheel removal before fully deflating the tire and opening it with suitable tire tools. Remove the old tube, inspect the tire interior and rim for sharp objects or damage, then install the replacement with its valve aligned and without trapping the tube under the tire edge. Refit the tire and wheel according to the manual, inflate to the specified pressure, and check tire seating, air retention, wheel security, and brake operation before riding.

Why does my Xiaomi 1S tire keep going flat after replacing the tube?

A remaining sharp object, damaged rim surface, pinched tube, or valve problem can make a new tube leak. Locate the leak and inspect the tire and rim before fitting another tube, and verify that the replacement size and inflation pressure match the scooter's requirements.

Should I replace a Xiaomi 1S inner tube myself or use a repair shop?

DIY replacement is reasonable if you have suitable tire tools and can follow the manual's wheel removal and refitting instructions confidently. Use a scooter repair shop if the tire will not release without excessive force, wheel wiring or brake components complicate removal, or you cannot verify secure reassembly.

All parts for Xiaomi Xiaomi 1S

Fitly Parts sells independent aftermarket replacement parts. Brand names are used only to identify compatible models and do not imply manufacturer affiliation.

Car with replacement cabin filter and wiper blades in a workshop

Cars & Auto

Looking for a part for your car?

Explore aftermarket car parts by category and make, matched to your exact model.

Explore Cars & Auto